Smart-UPS RT 8000VA (6400W), Extended Run, Rack Mount

Smart-UPS RT 8000VA (6400W), Extended Run, Rack Mount

• Supplies utility power to the connected loads in the event of a UPS overload condition or fault.
• Allows additional run time to be quickly added as needed.
• Maximizes battery performance, life, and reliability through intelligent, precision charging.
• Ensures clean, uninterrupted power to protected equipment while batteries are being replaced
• Automatically starts up the connected equipment upon the return of utility power.
• Prolongs battery life by regulating the charge voltage according to battery temperature.
• Provides remote management of the UPS over the network.
• Enables centralized management via the APC InfraStruXure Manager.
• Customize UPS capabilities with management cards.
• Quickly understand unit and power status with visual indicators.
• Provides management of the UPS via a serial port.
• Ensures clean, uninterrupted power to the loads when adding extra runtime to the UPS.
• Protects the initial investment in the UPS when migrating from tower to rack-mount environment.
• Install maintenance releases of firmware remotely using FTP.
• Increases availability by allowing a trained user to perform upgrades and replacements of the
• batteries reducing Mean Time to Repair (MTTR)
• Periodic battery self-test ensures early detection of a battery that needs to be replaced.
• Provides early-warning fault analysis ensuring proactive component replacement.
• Warns when a battery is not available to provide backup power.
• Provides notification of changing utility power and UPS conditions.
• Gives higher application availability by correcting poor frequency and voltage conditions without
• using the battery.
• Protects connected loads from surges, spikes, lightning, and other power disturbances.
• Minimizes installation costs by enabling the use of smaller generators and cabling.
• Ensures clean, uninterrupted power to protected equipment when generator power is used.
• Provides temporary battery power when the utility power is out.
• Easy recovery from overloads; no need to replace a fuse.
• Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

Technical Specifications

Output

• Output Power Capacity: 6400 Watts / 8000 VA
• Max Configurable Power: 6400 Watts / 8000 VA
• Nominal Output Voltage: 230V
• Output Voltage Note: Configurable for 220 : 230 or 240 nominal output voltage
• Efficiency at Full Load: 93%
• Output Voltage Distortion: Less than 3%
• Output Frequency (sync to mains): 50/60 Hz +/- 3 Hz user adjustable +/- 0.1
• Crest Factor: 3 : 1
• Waveform Type: Sine wave
• Output Connections: (1) Hard Wire 3-wire (H + N + G), (4) IEC 320 C13, (4) IEC 320 C19, (4) IEC Jumpers   
• Internal Bypass: (Automatic and Manual)
   

Input

• Nominal Input Voltage: 230V
• Input Frequency: 50/60 Hz +/- 5 Hz (auto sensing)
• Input Connections: Hard WIre 3-wire (1PH + N + G), Hwrd Wire 5 -wire (3PH + N + G)
• Input voltage range for main operations: 160 - 280V
• Other Input Voltages: 220,240
• Input Total Harmonic Distortion: Less than 7% for full load

Batteries & Runtime

• Battery Type: Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof
• Included Battery Modules: 4
• Typical recharge time: 2,2 hours
• Replacement Battery: RBC44
• RBC™ Quantity: 2

Communications & Management

• Interface Port(s): DB-9 RS-232, RJ-45 10/100 Base-T, SmartSlot
• Pre-Installed SmartSlot™ Card: AP9631
• Control panel: LED status display with load and battery bar-graphs and On Line, On Battery,Replace Battery, Overload and Bypass Indicators
• Audible Alarm: Alarm when on battery, distinctive low battery alarm, overload continuous tone alarm
• Emergency Power Off (EPO): Yes
   

Physical

• Height: 263.00 mm
• Width: 432.00 mm
• Depth: 736.00 mm
• Net Weight: 110.92 kg
• Shipping Weight: 129.10 kg
• Color: Black
• Units per Pallet: 1